Meet Malco in St. Louis for Comfortech 2015

15th September 2015 • Categories: Autobody Tools, Construction, HVAC, Made in USA, Products, Uncategorized

Calling all you convention goers! Malco Products Inc. will be out in full force at Comfortech 2015, taking place September 15-17 at America’s Center Convention Complex in St. Louis, Missouri. Malco will begin exhibiting at both #582 on Wednesday, September 16 and will be at their booth from 12:30-4:30 pm. On Thursday, September 17, Malco […]

READ MORE...

Made in USA

7th May 2015 • Categories: Autobody Tools, Construction, Made in USA, Product Introductions, Products

Presented here are some jottings and discussion threads intended to generate sharing of thoughts and feedback on the meaning and merits of “Made in USA” for you.  Please be civil so that all may be heard.  What does the term Made in USA Mean? The Federal Trade Commission (FTC), in brief, defines use of the […]

READ MORE...

Socket-Drive TORX Bit Kit

5th March 2015 • Categories: Connext-Handles, Construction, HVAC, New Product, Product Introductions, Products

ALL THE RIGHT CONNECTIONS  Paired with a Versatile CONNEXT3™ Quick-Connect Ratcheting Handle TXSK1 KIT CONTENTS 12 Socket Drive Torx Bits 3 Hex Drive Adapters for 1/4, 3/8 & 1/2 in Square Drives CONNEXT3™ Ratcheting Handle with 1/4 in Holder Durable Polymer Case   NOTE: Not for use with impact drivers. Sure, you can use other […]

READ MORE...

Easy on the checkbook and quick on the install!

3rd February 2015 • Categories: Construction, HVAC, New Product

Flexible Fiberglass  Duct is a popular choice for residential and commercial heating and cooling.  The flexible duct is often prone to kinks and sags that will restrict your air flow.  Malco has again come up with the perfect solution. Our FDS1 Flexible Duct Support will both eliminate air flow restrictions and increase efficiency. By doing […]

READ MORE...

They deliver BIG on the job

5th January 2015 • Categories: Construction, New Product

                With an overall length of only 7-1/8 inches (181 mm), the AVsMini easily goes to work where full-size aviation snips are challenged.  Forged steel jaws produce a long lasting, sharply defined cutting edge.  A 3/4 inch (19 mm) length of cut and sure-gripping serrations on the lower […]

READ MORE...

“PAN STYLE” MINI-BRAKE

9th December 2014 • Categories: Construction, Metal Bending, Mini Brake, New Product, Product Introductions, Products

GOES WHEREVER YOU NEED IT TO Fabricate drip pans, register boxes, and complex angled corners for flashing and fascia, right there on the job!   At just under 100 pounds (45 kg), if you remove just two screws, you can separate the Malco MB48B “Pan Style” Mini-Brake Anvil and frame to easily move it around the […]

READ MORE...

Ratchet up Efficiency!

6th November 2014 • Categories: Chain Link Fence, Fencing Tools, New Product

Offset Ratcheting Box Wrench is Ideal for installing or removing fasteners at chain link fence hook-up points. SMALL, LIGHTWEIGHT AND HUGELY PRODUCTIVE This versatile OFFSET RATCHETING BOX WRENCH provides easy fastener access and fast, two-way ratcheting  action with an effortless handle-swing motion.  Finger switches are easily accessible to change ratcheting direction.  A 25 degree offset […]

READ MORE...

TurboShear and TurboXTool Attachments

9th October 2014 • Categories: Asphalt Roofing Rools, Backerboard, Construction, Fiber Cement, Product Introductions, Products, TurboXTools, Uncategorized, Vinyl Siding

NOW EVEN MORE USER-DRILL FRIENDLY! Versatile NEW 1/4 inch Hex Drive Shafts Fit A Broader Range of Drills including Quick Release Impact Drivers Malco TurboShear and TurboXTool Drill Attachments  are now even more user-drill-friendly with the introduction of a new hex shank drive shaft that fits a broad range of 1/4 to 1/2 inch (6.35-12.7mm) […]

READ MORE...

MALCO AVs VERTICAL SNIPS

7th September 2012 • Categories: AV Vertical Snips, New Product, Product Introductions

Easy Gripping in Tight Spaces and Overhead The jaws of these sleek, compact and lightweight aviation snips are set at a 90-degree angle to the handles for easy upright gripping when cutting in confined spaces or overhead.  The user can follow circular or rectangular pattern cuts with either a pushing or pulling motion.  A serrated […]

READ MORE...

Malco GOLD STANDARD Hole Cutters handle up 20-gauge steel!

10th November 2009 • Categories: Hole Cutters, New Product, Product Introductions

Distinctive gold Cutter Bits, gold Bearings and a gold Pivot Pin are visual assurance that you have purchased the longest lasting, fastest cutting, easiest adjusting hole-cutting solution for sheet metal applications. With a 20-gauge capacity in galvanized steel (1.02mm) or mild steel (0.91mm), Malco Hole Cutters are ideal for making large or small diameter take-offs […]

READ MORE...